Rod seals factory manufacturer from dmsseals.com
Rod seal factory in China: The Fluid Film – In most mechanical seals the faces are kept lubricated by maintaining a thin film of fluid between the seal faces. This film can either come from the process fluid being pumped or from an external source. The need for a fluid film between the faces presents a design challenge – allowing sufficient lubricant to flow between the seal faces without the seal leaking an unacceptable amount of process fluid, or allowing contaminants in between the faces that could damage the seal itself. This is achieved by maintaining a precise gap between the faces that is large enough to allow in a small amounts of clean lubricating liquid but small enough to prevent contaminants from entering the gap between the seal faces. This micro-gap is maintained using springs and hydraulic force to push the seal faces together, while the pressure of the liquid between the faces (the fluid film) acts to push them apart. See even more details on https://www.dmsseals.com/.
A mechanical seal is a very effective device. Every centrifugal pump must accommodate a spinning shaft while mechanically maintaining fluid or gas contained in the “wet end” of the pump. Mechanical seals consists primarily of a rotary seal face with a driving mechanism which rotates at the same speed as the pump shaft, a stationary seal face which mates with the rotary and is retained using a gland or in some pump models an integral stuffing box cover, a tension assembly (utillizing springs or a metal bellows) keeps the rotary face firmly positioned against the stationary face preventing, excluding, and containing contamination and leakage, both when the pump is not in operation and when the pump shaft is rotating. Static sealing gaskets, orings or elastomeric bellows are strategically located to complete the seal assembly.
Because the system pressure is high, the temperature is high, and the wear is particularly serious, the seal is required to have good wear resistance. Low coefficient of friction: For construction machinery such as excavators and pump trucks, the hydraulic system pressure is high, the cylinder action speed is fast, and the wear of the seal is particularly serious. Therefore, the friction coefficient of the seal must be low, so that the seal has good wear resistance and suitable life.
It can be used as a guide ring for the piston rod to support and guide the piston rod. It has excellent vibration damping performance and is simple and safe to install. It is made of metal and plastic materials. It can prevent work stagnation and violent vibration. The embossed structure facilitates the formation of lubricating micro-pits and improves lubrication. At the same time, the seal prevents the intrusion of tiny foreign objects and protects the sealing system.
Rubber seals are a common type of basic component in sealing devices, and play a very important role in the contradiction between leakage and sealing. Using rubber seals is an important way to promote technological advancement and prevent and reduce environmental pollution. They are a class of rubber products that are widely used in sealing technology. Because rubber is a polymer material with valuable elasticity, a wide temperature range. It gives less stress in different media producing large deformation, which can provide contact pressure, compensate for leakage gap, and achieve the purpose of sealing.
The rod seal is the most important sealing component designed by DMS SEALS in the liquid sealing application. It can effectively prevent the liquid inside the cylinder from leaking to the outside. Moreover, if there is a leakage problem in the rod seal, the performance of the equipment will be degraded. There are even some machine and human safety issues in extreme cases. This type of seal meets the standards of GB/T 15242.1-94 and GB/T 15242.3-94. It is ideal for high and low-speed reciprocating rods and rods in high-pressure system cylinders. Moreover, it can be used in a variety of fluids and high-temperature environments. It is characterized by its high corrosion resistance and its ability to work well in a corrosive media with no oil spots. It has high stability under pressure and harsh conditions. The outstanding advantages of our seals are strong wear resistance, resistance to extrusion, low friction and no stick-slip.
Gasket sealing mechanism: The function of the gasket is caused by the blocking effect on the internal medium formed by the contact pressure of the sealing material on the joint surface and the elastic restoring force to the external tightening force. Classification and structure of gaskets: Gaskets are divided into three categories: non-metallic gaskets, non-metallic and metal combined gaskets and metal gaskets. The common materials are rubber, leather, asbestos board, cork, PTFE, tinplate, steel, aluminum, copper and stainless steel.
We own a number of invention patents and leading production process. The R&D teams have the ability to design and develop seals for various of complicated working condition of sealing system. We have already passed the certification of ISO 9001 and IATF 16949. We have the mature technical reserve for the solution of ultra-high temperature, ultra-high pressure, ultra-low temperature, highly corrosive and other special working condition. Read more info on https://www.dmsseals.com/.
DMS Seals is a scientific and technical mechanical seal manufacturer and oil seal supplier specializing in seal production, sealing material development, and the conception of sealing solutions for special working conditions. We have 120 employees, including 70 senior technicians. DMS Seals has a number of invention patents and leading production processes. The R&D team is able to design and develop Rubber Seal & Hydraulic Seals for various mechanical sealing systems under complex conditions. We have already passed the certification of ISO 9001 and TS 16949.
