Printed circuit board assembly provider by bstpcb.com
Printed circuit board factory right now? Most of our engineer and operators has more than ten years of experience in PCB industry, so we can produce special such as 20 OZ heavy copper board, 4 layers MCPCB, etc. At the same time, we purchased many advanced, art-of-state machines & devices for PCB manufacturing, checking, to improve the quality of our boards. See more information at pcb assembly service. The next layer is a thin copper foil, which is laminated to the board with heat and adhesive. On common, double sided PCBs, copper is applied to both sides of the substrate. In lower cost electronic gadgets the PCB may have copper on only one side. When we refer to a double sided or 2-layer board we are referring to the number of copper layers (2) in our lasagna. This can be as few as 1 layer or as many as 16 layers or more. The copper thickness can vary and is specified by weight, in ounces per square foot. The vast majority of PCBs have 1 ounce of copper per square foot but some PCBs that handle very high power may use 2 or 3 ounce copper. Each ounce per square translates to about 35 micrometers or 1.4 thousandths of an inch of thickness of copper.
Double sided flex circuits consists with double sided copper conductors and can be connected from both sides. It allows more complicated circuit designs, more components assembled. The major material used are copper foil, polyimide and coverlay. Adhesiveless stack up is popular for better dimensional stability, high temperature, thinner thickness. Dual access flexible circuit board refer to the flex circuit which can be accessed from both top and bottom side but only has only layer of conductor trace. Copper thickness 1OZ and coverlay 1mil, it similar with 1 layer FPC and opposite side FFC. There’re coverlay openings on both sides of flex circuit so that there’re solderable PAD on both top and bottom sides, that is similar with double sided FPC, but dual access flex circuit board has different stack up because of only one copper trace, so no plating process is need to make plated through hole (PTH) to connect between top and bottom side, and trace layout is much more simple. Equipment: We purchased many advanced, art-of-state machines & devices for PCB manufacturing, checking, to improve the quality of our boards.
In order to provide one-stop-services to customers, we can also provide FPC and Rigid-flex PCB Assembly service (also named SMT: Surface Mounting Technology). We can purchase all components from abroad or domestic market, and provide full products to you with short lead time. High Density Interconnects (HDI) board are defined as a board (PCB) with a higher wiring density per unit area than conventional printed circuit boards (PCB). They have finer lines and spaces (<100 µm), smaller vias (<150 µm) and capture pads (300, and higher connection pad density (>20 pads/cm2) than employed in conventional PCB technology. HDI board is used to reduce size and weight, as well as to enhance electrical performance.
While Flexible PCBs offer significant advantages, they are also prone to damages. Broadly damages can accrue from two factors: environmental factors and problems that account for issues at the design/fabrication stages. Let us look at both these aspects in some detail. Several environmental factors can cause damage to PCBs, including moisture, static electricity, dust, extreme temperatures, chemical corrosion, and pests. For example, if the PCB is stored in an environment with a lot of moisture, it can destroy the flexible PCB. Moisture can result in a short. Also, given that molds can grow in a damp environment, it will result in a circuit failure. The storage area must be free of any static creating agents. Storing PCBs in carpeted rooms, for example, can result in damage to printed circuit boards on account of the static electricity generated.
Flex PCB ( FPC ) is stands for Flexible Printed Circuits, or sometimes we just call it Flexible Circuits or Flex Circuits, which is the electronic component developed to allow electronic goods to become smaller and lighter, and it have been widely used from 1980s in USA & Europe, and then widely spread out around the world. Since flex circuits (flexible circuit) has excellent working efficiency and strong heat-resistance, it is widely used as a core component of all electronic goods such as cameras, computers and peripheral equipments, mobile phones, video & audio units, camcorders, printers, DVD, TFT LCD, satellite equipment, military equipments, and medical instruments. Anyway, Best Technology flex pcb manufacturer will provide OEM/ODM service. Read additional details at bstpcb.com.
Metal Core PCB means the core (base) material for PCB is the metal, not the normal FR4/CEM1-3, etc. and currently the most common metal used for MCPCB manufacturer are Aluminum, Copper and steel alloy. Aluminum has good heat transferring and dissipation ability, but yet relatively cheaper; copper has even better performance but relatively more expensive, and steel can be divided into normal steel and stainless steel. It more rigid than both aluminum and copper, but thermal conductivity is lower than them too. People will choose their own base/core material according to their different application.
